Мастер-классы по украшению тортов Cake Decorating Tutorials  (How To's) Tortas Paso a Paso

Вернуться   Мастер-классы по украшению тортов Cake Decorating Tutorials (How To's) Tortas Paso a Paso > Cake Decorating Tutorials > How To Cake Borders


Ваш профиль:
Your Avatar
Забыли пароль?
Регистрация



 
Ответ

How to create a simple pleated tier

 
LinkBack Опции темы Поиск в этой теме
  #1  
Старый 02.07.2014, 17:43
Администратор
 
Регистрация: 23.04.2014
Сообщений: 513
По умолчанию How to create a simple pleated tier

Огромная благодарность rosycakesnz за Мастер-класс

Название: 1_1.jpg
Просмотров: 0

Размер: 141.8 Кб

Название: 2.jpg
Просмотров: 0

Размер: 201.6 Кб
This is a short tutorial that gives some insight into how I make a simple pleated tier. By no means am I implying that this particular pleat design was created by me, I have seen it done many times but I have also been asked a lot of questions regarding how I achieved it, in particular the folding of the pleat underneath the cake. I hope the below helps you to achieve a pleat you are happy with.
Название: 3.jpg
Просмотров: 0

Размер: 71.3 Кб
This particular pleated design is for a tier that is going to have another tier above it. The design does not cover the entire top of the cake. Prior to making the pleats I score or mark the size of the above tier into the top of the cake. This is the guide for how far on top of the cake the pleats are to sit. This cake has been covered in a thin fondant base, this is absolutely not necessary, on all of my pleated cakes I do a very thing fondant base in the same colour, this gives a really tidy finish when the thin pleated effect is adhered, I also find the pleats stick to the fondant a lot easier. In addition to that, if you have any gaps in your pleats (which does not apply so much to this particular design, then they wont show due the base layer being the same colour)
Название: 4.jpg
Просмотров: 0

Размер: 87.1 Кб
The key to creating the pleats that fold under the cake is to elevate the cake on a very sturdy bowl. The cake remains there during the whole process and the pleats are adhered to the cake and folded under the cake base. It is important that once the pleats are completed to carefully place the cake onto a cake board (or if that is not ready yet just place it onto a flat surface that is lined with baking paper. This will ensure the pleats at the bottom dry in the perfect way rather than drying while the cake is elevated and then being placed onto a flat surface, this may cause the bottom pleats to crush or break. In addition, ensure pressure is applied when placing your completed cake onto a cake board or lower tier and use a level to make sure the cake is sitting flush, so that the pleats don’t cause the cake to be lop-sided.
Название: 5.jpg
Просмотров: 0

Размер: 122.2 Кб
Brush entire cake with edible glue, shortening or water. If it dries while your working you may need to reapply.
Название: 6.jpg
Просмотров: 0

Размер: 152.7 Кб
Also a few cm’s under the cake
Название: 7.jpg
Просмотров: 0

Размер: 124.0 Кб
Roll out a very thing piece of fondant. Measure the height of your cake and add a few cm’s to the length. Enough to fold over the top of the cake and enough for a wee bit to fold underneath.
Название: 8.jpg
Просмотров: 0

Размер: 137.3 Кб
Lay fondant over 3 paper straws (Dowels or skewers also work). Use your fingers to smooth over the straws and create grooves in between the straws.
Название: 9.jpg
Просмотров: 0

Размер: 127.7 Кб
Pinch the tops of the straws together at the top, this is creating the pleats.
Название: 10.jpg
Просмотров: 0

Размер: 130.6 Кб
Remove the straws, then gather the opposite ends together as pictured.
Название: 11.jpg
Просмотров: 0

Размер: 108.9 Кб
Using the guideline marked the top of the cake, adhere the first pleat to the top of the cake.
Название: 12.jpg
Просмотров: 0

Размер: 146.6 Кб
Trim the bottom of the pleat so it over hangs a little bit.
Название: 13.jpg
Просмотров: 0

Размер: 137.5 Кб
Fold the pleat under the cake and apply pressure to the cake base.
Название: 14.jpg
Просмотров: 0

Размер: 102.2 Кб
Every pleat will be different but it will now resemble something like this.
Название: 15.jpg
Просмотров: 0

Размер: 125.8 Кб
Apply a small amount of edible glue or water to the seam where the next pleat will overlap.
Название: 16.jpg
Просмотров: 0

Размер: 113.3 Кб
All of the following pleats are created in the same fashion as the first one. The only difference is that they a small “hem” is created on the edge that will over lap the prior pleat.
Название: 17.jpg
Просмотров: 0

Размер: 114.1 Кб
Turn the “hemmed” side over, lay over the straws and create the pleat.
Название: 18.jpg
Просмотров: 0

Размер: 104.2 Кб
Adhere the next pleat. See how I am applying pressure to the top of the pleat, almost squishing it down where it meets the guideline.
Название: 19.jpg
Просмотров: 0

Размер: 137.7 Кб
Do the same at the base of the cake.
Название: 20.jpg
Просмотров: 0

Размер: 130.9 Кб
Continue making pleats the whole way around the cake until it reaches the first pleat.
Ответить с цитированием
Ответ

Метки
how to create a simple pleated tier

Опции темы Поиск в этой теме
Поиск в этой теме:

Расширенный поиск






©2020 Lovely Tutorials
Search Engine Friendly URLs by vBSEO