Cake Decorating Tutorials  (How To's) Tortas Paso a Paso

Вернуться   Cake Decorating Tutorials (How To's) Tortas Paso a Paso > Do-It-Yourself


Ваш профиль:
Your Avatar
Забыли пароль?
Регистрация



 
Ответ

Ленторез для мастики и теста (делаем сами)-DIY multi-blade ribbon/strip cutter for fo

 
LinkBack Опции темы Поиск в этой теме
  #1  
Старый 29.07.2011, 09:26
Администратор
 
Регистрация: 07.09.2010
Сообщений: 7,940
По умолчанию Ленторез для мастики и теста (делаем сами)-DIY multi-blade ribbon/strip cutter for fo

МК взят с сайта http://blogs.mail.ru/mail/loravo/BD26A7695DEB6AA.html
автору-Лариса Вольницкая (loravo) , огромная благодарность!!!
слова автора

Название: DIY-multi-ribbon-strip-cutter-01.jpg
Просмотров: 38

Размер: 67.6 Кб
кусок пластиковой водоброводной трубы (у меня полудюймовая труба для питьевой воды, см картинку ниже)
Название: DIY-multi-ribbon-strip-cutter-02.jpg
Просмотров: 38

Размер: 75.4 Кб

Название: DIY-multi-ribbon-strip-cutter-03.jpg
Просмотров: 38

Размер: 68.2 Кб
прут (спица) с резьбой, такого же диаметра, как отверстие в ноже. Как правило, они продаются длинными кусками. Нужную длину легко отрезать при помощи обычной ножовки по металлу.
Название: DIY-multi-ribbon-strip-cutter-04.jpg
Просмотров: 38

Размер: 71.6 Кб
2 гайки, с таким же диаметром отверстия и шагом резьбы, как и у прута
Название: DIY-multi-ribbon-strip-cutter-05.jpg
Просмотров: 38

Размер: 68.5 Кб
круглые ножи для пиццы со съемным креплением (болт и гайка) - минимум 2ш
Название: DIY-multi-ribbon-strip-cutter-06.jpg
Просмотров: 36

Размер: 60.2 Кб
Гайку открутить, нож снять. Будут использоваться только сами колесики-ножи.
Название: DIY-multi-ribbon-strip-cutter-07.jpg
Просмотров: 34

Размер: 74.2 Кб
В общем, сначала находим нужные ножи (колесики) для пиццы в хозяйственном, а потом топаем на строительный рынок или в соответствующий магазин, и находим все остальное.

Трубка нам нужна для изготовления спейсеров (разделителей) между ножами. Их ширина будет определять ширину нарезаемых нами лент. Пластиковые трубки легко режутся спец-ножами для ПВХ и пластиковых труб. Если аккуратно, то и ножом они тоже режутся неплохо. Вы можете в любой момент изготовить спейсер для ленты определенной ширины.
Название: DIY-multi-ribbon-strip-cutter-08.jpg
Просмотров: 38

Размер: 86.9 Кб
Если на свободные концы спицы надеть лишние куски трубки и опереть о них пальцы во время работы, ленторез будет скользить очень быстро, легко и гладко.
Название: DIY-multi-ribbon-strip-cutter-09.jpg
Просмотров: 35

Размер: 85.9 Кб

Название: DIY-multi-ribbon-strip-cutter-10.jpg
Просмотров: 32

Размер: 81.4 Кб

Название: DIY-multi-ribbon-strip-cutter-11.jpg
Просмотров: 34

Размер: 55.4 Кб

Название: DIY-multi-ribbon-strip-cutter-12.jpg
Просмотров: 34

Размер: 40.8 Кб

Название: DIY-multi-ribbon-strip-cutter-13.jpg
Просмотров: 34

Размер: 81.4 Кб

Название: DIY-multi-ribbon-strip-cutter-14.jpg
Просмотров: 34

Размер: 75.1 Кб





Today I'd like to share with you my new favorite tool: the ribbon cutter. But not just any cutter! There are a few readily available products on the market, but, unfortunately, they either hard to get hold of, or create more of a headache then anything, or they cost a small fortune and still I wish they were performing better.

This one you can easily make yourself, it can make almost any width strips and ribbons out of any rollable moldable medium that can be cut with a pizza cutter. And it makes beautiful clean cuts on any thickness of rolled fondant, dough or clay!




OK, enough talking! Get ready for a quick trip to kitchen tool section of your nearest supermarket, department store or even a dollar store, and then another quick stop at hardware store (like Home Depot or alike), and you are done!

Get a few (minimum 2 to begin with) pizza cutters. Not any pizza cutters, but the ones where the blade is screwed with a nut and bolt type of fixture. Unscrew it and take apart. You are going to need the blades only.

Take them with you to the nearest hardware store and now find a threaded rod (ask for help if you are not sure where to look for that). They are usually long so you can make a few different length ribbon cutters for yourself, or make a couple extra for a nice gift (just cut them with a hacksaw). They also come in a few different diameters.

Your goal would be to find matching rod diameter for the hole in your pizza blade. They should fit snugly. Once you found the rod, get two metal nuts of the same size for it.

Now we need spacers for our cutter, they will determine the widths of our ribbons and strips. Get the PEX drinking water pipe (it's made of flexible, but sturdy plastic, see image #3). Mine came in a length of a few feet (may be 10), and cost only a couple bucks. It can be easily cut with PVC plastic pipe cutters.

Cuts like butter! You can measure it with a ruler, make marks, and cut as thin or as thick as you like, and because you have a lot of it, you will be able to make a huge selection of whatever width spacers you might need, and continue making them whenever you need a new, different size spacer.

And if you slide two pieces of pipe on the sides of the rod to rest your fingers at while cutting, you'll get a very smooth consistent roll!



Put a few blades on it to make many ribbons at once, or just two to make one ribbon.



Make one with fluted blades if you are lucky to find that kind of pastry cutters.
Ответить с цитированием
Ответ

Метки
diy multi-blade ribbon/strip cutter for fondant, dough, gum paste, playdough, polymer clay (fimo) or clay, ленторез для мастики и теста (делаем сами)

Опции темы Поиск в этой теме
Поиск в этой теме:

Расширенный поиск






©2022 Lovely Tutorials