Показать сообщение отдельно
  #4  
Старый 03.09.2011, 20:20
Ariana Ariana вне форума
Администратор
 
Регистрация: 07.09.2010
Сообщений: 7,940
По умолчанию Mickey Mouse figure tutorial on cake

Mickey Mouse

Premo Sculpey colors: cadmium red, black, white beige
Sculpey III colors: dusty rose, yellow
Kemper clay cutters: 5/8" circle, 3/4" heart (or use these patterns)




Название: Mickey Mouse figure tutorial on cake Step 1.jpg
Просмотров: 190

Размер: 382.8 Кб
1. Shoes: Roll two 3/4" yellow balls into eggs. Lay them on their sides and press to slightly flatten the small ends. Pinch to slightly indent the sides. Attach with the small ends together and toes pointed out. Flatten two 5/16" yellow balls and press onto the ankles.

2. Legs: Roll a 1/4" x 7/8" black log; cut in half. Insert a straight pin into each leg so it exdents equally on both ends. Press one leg onto each ankle.

3. Shorts: Roll a 7/8" red ball and slice 1/8" off the top. Roll two 7/16" red balls and flatten to 1/4" thick. Pinch the edges and attach side by side to the bottom of the ball. Smooth the seams. Press onto the leg pins. Use the pin to make wrinkle lines in the shorts front and back. Roll two 3/16" white balls into ovals, flatten and attach to the shorts front as shown for buttons. Repeat on the back.

4. Chest: Roll a 9/16" black ball into a cone. Press the flat edge onto the top of the shorts and slightly flatten the chest. Round the top slightly and insert a pin so 1/4" extends.

Название: Mickey Mouse figure tutorial on cake Step 2.jpg
Просмотров: 212

Размер: 442.2 Кб


5. Arms: Roll a 1/4"x2" black log and cut in half. Taper one end of each and attach this end to the top of the cone - Mickey has hardly any shoulders! Bend the arms at the elbows so they extend outward as shown. Insert a straight pin into each arm so half extends. Bake (see inside the back cover); let cool.

6. Gloves: Shape a 1/2" white ball into a mitten. Use the X-acto knife to make two 1/4" slices in the wide end, forming three fingers. Pull the fingers apart round and smooth the edges. Use the neddle to draw three lines on the back. Repeat to make another glove the reverse of the first.

7. Flatten two 1/4" white balls to 1/8" thick and attach one to the end of each arm. Press a glove onto each arm so the thumbs are up and slightly towards the back.

8. Head: Roll a 1" black ball (don`t put it on the body yet). Flatten beige to 1/16" thick and use the heart cutter to cut the face. Attach the center front of the ball.
9. Shape a 7/16" beige ball into a 1 3/4" long log. Press over the bottom of the heart, then slightly flatten, tapering the ends and pinching a triangular chin. Slightly smooth the seams.

10. Muzzle: Roll a 3/8" beige ball into an oval and flatten one end.Pinch the edges and attach above the chin as shown - the top should line up with the black corners of the head. Smooth the seam and the corners where the muzzle meets the cheeks.

11. Use the needle to draw the smile; make a tiny V on each end. Use your fingertips to soften the edges and open the mouth slightly. Roll a 1/8" rose ball, flatten and press into the center of the mouth for the tongue. Use the needle to indent the center.

12. Eyes: Roll two 3/16" white balls into ovals and flatten. Attach side by side, 1/16" apart, above the muzzle. Flatten two 1/16" black balls into ovals and press one onto the center bottom of each eye. Nose: Roll a 3/16" black ball into an oval and attach one small end to the ne of the muzzle. Attach the head to the body so Mickey is looking slightly upward. Ears: Flatten black clay to 1/5" and use the currle cutter to make two ears. Smooth and round the edges of the tops. Press edgewise onto the top back of the head, 3/8" apart, flat sides to the front. Bake; let cool.
Ответить с цитированием