Показать сообщение отдельно
  #18  
Старый 11.05.2016, 10:29
Arianochka Arianochka вне форума
Администратор
 
Регистрация: 10.03.2016
Сообщений: 1,003
По умолчанию

Огромная благодарность Lisa Templeton за Мастер-класс

Название: 1.jpg
Просмотров: 3

Размер: 148.2 Кб
Decorating time:
2+ hours; Make over two days to allow drying time.
Skill level:
All
You will need:
  • Ivory or white Pettinice
  • Crisco
  • Tylose powder
  • Edible glue (tylose and water)
  • Pme modelling tool
  • Scriber needle tool
  • Half a large sturdy plastic bag
  • Floral wire ( around 22)
  • Wire cutter
  • Veiner hydrangea or rose veiner (optional)
  • Lime or Spring green petal dust
  • Paintbrushes for glue and dusting
  • Cell board (optional)



Making the hydrangea buds

Название: 2.jpg
Просмотров: 3

Размер: 42.3 Кб
Take your 22 Gauge wire and cut one piece into 2 or 3.
Название: 3.jpg
Просмотров: 2

Размер: 32.0 Кб
Then using the wire cutter gently bend over the tips to make wee tiny hooks.
Название: 4.jpg
Просмотров: 0

Размер: 56.3 Кб
Roll tiny balls. (I use two smallest holes on cell board as guide.) In nature, buds are different sizes so be sure to vary yours too.
Название: 5.jpg
Просмотров: 2

Размер: 41.6 Кб

Название: 6.jpg
Просмотров: 0

Размер: 68.6 Кб
Place your little ball of paste on the end of your wire and gently roll the bottom with your fingers until it sticks well and has a rounded top.
Название: 7.jpg
Просмотров: 2

Размер: 80.3 Кб

Название: 8.jpg
Просмотров: 0

Размер: 53.8 Кб
Using the scriber, firmly emboss a cross at the top as shown. Either hang or stick into a polystyrene dummy to allow it to dry. Make as many as you can these are your buds and flower centers. To make a display you need plenty as these are used for both the small flowers and buds. I used 60 for the piece shown.

Making the hydrangea petals

For best results, begin making your petals only after your hydrangea buds have dried. I usually make eight petals at a time.

With my sugar flower method, you do not need special cutters. You will create your hydrangea petals using a sturdy plastic bag (such as a snap lock, or ziplock), which you will need to cut open along one of the side seams so it opens like a book. Open your cut plastic bag, place a small ball of paste inside and fold the plastic over it to begin the next steps.
Название: 9.jpg
Просмотров: 4

Размер: 49.8 Кб
Using your thumb gently pull down to make the pointed bit at the bottom, then using your fingers push out the shape of the petal.
Название: 10.jpg
Просмотров: 0

Размер: 47.8 Кб
Remember to make them small about 1 cm to 1.5 cm long. Thin the edges of the petal with the side of your finger.
Название: 11.jpg
Просмотров: 0

Размер: 54.5 Кб
Using a Hydrangea veiner or Rose veiner press in the veins.
Название: 12.jpg
Просмотров: 2

Размер: 49.3 Кб

Название: 13.jpg
Просмотров: 2

Размер: 60.7 Кб

Название: 14.jpg
Просмотров: 0

Размер: 65.4 Кб

Название: 15.jpg
Просмотров: 0

Размер: 80.3 Кб

Название: 16.jpg
Просмотров: 1

Размер: 74.7 Кб
If you don't have a veiner, at STEP 9 above, emboss the veins with the edge of your fingernail while it is still in the plastic bag. Soft pressure is fine as you don't want to tear the bag.
Ответить с цитированием